The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
We've come across the article involving Installing A Bathtub below on the internet and decided it made sense to share it with you over here.
Setting up a bath tub isn't precisely rocket science, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably difficult task. If the old tub is readily easily accessible, the project can relocate rapidly; if you need to open up a wall to get rid of the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the new one. Make certain you have qualified on your own for the work and also fit trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is far better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your shower room if you have already acquired a brand-new tub and also don't need to transform the arrangement of your previous water pipelines.
Your tools and also product checklist should consist of the following:
Getting ready for the Installation
Firstly, the supporting frame supplied with the bath must be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome because of the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the required placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also readjusting the feet on the bathtub until the spirit level reads level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
Switch on the supply of water and also examine all joints and also new pipework for leaks as well as tighten them if required. Fill up the bathtub as well as likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait till the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Protect the tap in place with the producer given backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former type must be connected to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a rigid seal, causing the water to penetrate the wall surface in between the bath and the tiling, leading to problems with moisture as well as feasible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can crack relatively very early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on A Step-by-Step Guide to Installing a Bathtub? Create feedback down below. We'd be pleased to listen to your suggestions about this post. Hoping that you come back again in the near future. So long as you enjoyed reading our post plz remember to pass it around. I cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Professional touch awaits. Report this page